|
DESCRIPTION: |
|
SUPERIOR JOINT SEAL-80 NON
SAG is a two component, 100% solids, equal volume mix,
semi-rigid, heavy duty epoxy joint filler for industrial
floors and walls. |
|
USES: |
|
Joint filler for industrial
concrete floors subjected to hard wheeled vehicles such
as forklifts. SUPERIOR JOINT SEAL-80 NON SAG may be used
for repairing spills, cracks and damaged joints in
floors and walls. |
|
ADVANTAGES: |
|
Easy -to-use 1:1 by volume
mix ratio.
Non-sag for vertical
application.
Color coded to insure
thorough mixing.
Retains resiliency; does
not become brittle with age.
Excellent wear
resistance.
Semi-rigid support joint
edges and to carry heavy loads across the joint. |
|
SURFACE
PREPARATION: |
|
Area must be clean and dry.
Saw-cuts shall be blown clean and dry with compressed
air to remove all excess moisture and debris. Remove
curing and sealing compounds. |
|
MIXING
AND APPLICATION: |
|
Stir both A and B
components before mixing together. Mix equal volumes of
Part A and Part B. Mix thoroughly with a heavy duty, low
speed drill fitted with a mixing paddle. Mix until a
uniform gray color with no streaks is evident. Be sure
to scrape the sides and bottom of the mixing pail.
For neat and easy
application, tape both sides of joints with masking
tape. Apply with bulk caulking gun, disposable plastic
dispenser or knife into joint with a spatula or trowel.
Fill joints flush to the top or slightly higher than the
surrounding surface. Tool joints off flush before
SUPERIOR JOINT SEAL-80 NON SAG starts to set. Remove all
tape and clean spills and tools immediately upon
completion of installation.
|
VOLUME
REQUIREMENTS FOR FILLING JOINTS (Linear feet per gallon) |
| Joint |
1/4 |
˝ |
3/4 |
1 |
1 1/4 |
1 ˝ |
|
1/4 |
306.0 |
- |
- |
- |
- |
- |
|
˝ |
154.0 |
77.0 |
- |
- |
- |
- |
|
3/4 |
102.7 |
51.3 |
34.2 |
- |
- |
- |
|
1 |
77.0 |
38.5 |
25.7 |
19.3 |
- |
- |
|
1 1/4 |
61.6 |
30.8 |
20.5 |
15.4 |
12.3 |
- |
|
1 ˝ |
51.3 |
25.7 |
17.1 |
12.8 |
10.3 |
8.6 |
|
1 3/4 |
44.0 |
22.0 |
14.7 |
11.0 |
8.6 |
7.3 |
|
2 |
38.5 |
19.3 |
12.8 |
9.6 |
7.7 |
6.4 |
|
2 ˝ |
30.8 |
15.4 |
10.3 |
7.7 |
6.2 |
5.1 |
|
3 |
25.7 |
12.8 |
8.6 |
6.4 |
5.1 |
4.3 |
|
|
LIMITATIONS: |
|
Do NOT apply when
temperature is below 50°F.
Do NOT use in true
expansion joints, exterior joints, tooled joints, or
joints subject to chemical exposure.
Do NOT install in
concrete less than 28 days old.
Best results are
obtained when applied 3 to 6 months after construction.
Do NOT use compressible
backer rod. |
|
CLEAN
UP: |
|
Clean tools and equipment
immediately with a suitable solvent such as xylene or
lacquer thinner. |
|
PACKAGING: |
|
2 gallon units
10 gallon units |
|
CAUTION: |
|
For professional use only.
Epoxy systems can cause delayed dermatitis. Avoid
prolonged contact with skin. See Material Safety Data
Sheet for proper handling and required safety equipment. |
|
PROPERTIES
AT 77°F
| Mix ratio by volume |
1:1 |
| Viscosity |
Thixotropic paste |
| Color |
Part A White; Part B
Black; Gray mixed |
| Pot Life (100 Grams) |
15-25 minutes |
| Hardness Shore A (ASTM
D-2240) |
80 ± 10 |
| Hardness Shore D (ASTM
D-2240) |
50 ± 5 |
| Tensile Elongation
(ASTM D-638) |
25% |
| Tensile Strength (ASTM
D-638) |
400-600 psi |
| Compressive Yield (ASTM
D-695) |
1,530 psi |
| Initial Cure |
6 - 8 hours |
| Traffic Ready |
8 - 12 hours |
| Shrinkage |
Nil |
| Shelf Life |
2 years |
|
