 |
Item # SST, Superior SuperTop
Pre-Measured Topping, Contains Primer and Aggregate
SUPERTOP is a structural epoxy mortar topping which provides hard-surfacing, skid proofing and corrosion protection of either new or eroded old concrete floor surfaces. SUPERTOP cures to an "industrial" tough, chemical and wear resistant surface. SUPERTOP will provide protection against spillage of most acids, alkalies,
fats, oils, sugars and other damaging substances. |
|
View Technical Bulletin for physical properties of type selected.
Uses
- Surfacing and patching concrete floors.
- Skid resistant surfacing.
- Chemical resistant flooring.
Advantages:
- Physical properties far exceeding those of concrete.
- Easy-to-use pre-measured kits.
- 100% solids - no shrinkage.
- Excellent abrasion resistance
- Seamless, slip resistant and easily cleaned.
- Available in standard, low temp and chemical resistant versions.
Surface Preparation
Surface must be clean, sound, dry and free of any oils, grease, curing compounds, dust, laitance or any other contaminants. This may be accomplished by sand blasting, water blasting or some other mechanical means. New concrete surfaces should be acid etched with muriatic acid and rinsed thoroughly. Surface may be dry or damp, but must be free of standing water.
Mixing & Application
- Pour contents of Binder Part A and Part B into empty pail and mix thoroughly with spatula or a slow speed 1/2" drill with paddle.
- Add aggregate slowly, while mixing, to the mixed binder.
- Mix until aggregate is thoroughly wet, approximately 2 minutes.
- Apply to prepared surface with a trowel.
|
 |
|
Limitations
- Do NOT apply when temperature is below 50oF.
- Do NOT apply to latex modified mortar or concrete.
- Do NOT use on floors subjected to constant temperatures in excess of 180oF.
Clean Up
Clean tools and equipment immediately with a suitable solvent such as xylene
or lacquer thinner.
Caution
For professional use only. Epoxy systems can cause delayed dermatitis. Avoid
prolonged contact with skin. See Material Safety Data Sheet for proper
handling and required safety equipment.
Specification
- Packaging: Kit contains binder and blended aggregate in plastic 5 gallon
mixing container. Kit covers for 35 square feet
|
Estimation Chart
TABLES & ESTIMATING DATA
EPOXY MORTAR YIELD PER GALLON
OF EPOXY BINDER |
COVERAGE PER GALLON
OF EPOXY MORTAR
(EPOXY BINDER + SAND) |
COVERAGE
FOR COATING OR MEMBRANES |
Epoxy Binder Gallons |
Aggregate Gallons# |
Mortar Gallons |
1 |
1 |
1.6 |
1 |
2 |
2.2 |
1 |
3 |
2.8 |
1 |
4 |
3.4 |
1 |
5 |
4.0 |
#Flint Shot approximately 12-14
Pound/Gallon.
With other aggregates, figures will vary with
size and amount of entrained air.
|
Thickness
- Inches |
Coverage
- Square Feet |
1/16 |
25.7 |
1/8 |
12.8 |
3/16 |
8.6 |
1/4 |
6.4 |
3/8 |
4.3 |
1/2 |
3.2 |
|
Thickness of
Coating Applied
(1000 mils = 1 inch) |
Coverage per U.S.
Gallon
100% Solids System |
1/4 inch = 250 mils |
6.4 Square Feet |
3/16 inch = 187.5 |
8.5 Square Feet |
1/8 inch = 125mills |
12.8 Square Feet |
100mils |
16.0 Square Feet |
1/16 inch = 62.5 mils |
25.5 Square Feet |
50 mils |
32.0 Square Feet |
1/32 inch = 31.25 mils |
51.0 Square Feet |
20 mils |
80.0 Square Feet |
1/64 inch = 15.625 mils |
102.0 Square Feet |
10 mils |
160.0 Square Feet |
5 mils |
320.0 Square Feet |
1 mil |
1600.0 Square Feet |
If coating contains a solvent which
will evaporate, thickness of coating
will be reduced by same percentage
as solvent loss. |
|
 |