|
DESCRIPTION: |
|
SUPERIOR
GLOSS is a two component, 100% solids, flexibilized,
blush resistant epoxy wall and floor coating. SUPERIOR
GLOSS produces a dense, tile-like coating for protection
of walls and floors against corrosion and deterioration
caused by water, chemicals and heavy traffic. |
|
USES: |
| Excellent
for use on concrete block and similar surfaces as a
graffiti-resistant decorative coating.
With aggregate broadcast
onto wet surface, produces an easy-to-clean,
slip-resistant coating.
Tile-like coating for
protecting walls and floors against water, chemicals and
heavy traffic. |
|
ADVANTAGES: |
|
Blush-resistant, even in high humidity.
High gloss.
100% solids.
Resistant to water
spotting.
Chemical resistant |
|
GRADES
AND TYPES: |
|
A) SUPERIOR
GLOSS (standard): surfaces. Available in clear and
colors.
B) SUPERIOR GLOSS
(non-sag): For vertical applications where non-sag
properties are required. Available only in color.
C) SUPERIOR GLOSS CLEAR (LV)
- For use as a primer or penetrating sealer. |
|
SURFACE
PREPARATION: |
| Surface
must be clean, sound, dry and free of all foreign
materials such as oils, grease, loose paint, dust and
laitance. This may be accomplished by sand blasting or
scarifying, followed by an air blast to remove dust and
debris from the application area. New concrete surfaces
should be acid etched, rinsed thoroughly and allowed to
dry. |
|
MIXING
AND APPLICATION: |
| 1. Stir
each component separately.
2. Clear: Mix 2 volumes
of part A with 1 volume of part B.
Pigmented: Mix 1 volume
of part A with 1 volume of part B.
3. Mix thoroughly, being
sure to scrape the sides and bottom, with a strong
mixing stick or slow-speed drill equipped with a paint
propeller.
4. Do not mix more than
can be applied in 30 minutes.
5. As a coating, apply
mixed material by brush or roller.
For best results, two
coats should be applied. Allow the first coat to cure
overnight. Apply the second coat within 24 hours. If
more time than 24 hours has elapsed, a light sanding of
the first coat is required. SUPERIOR GLOSS can be placed
as thick as desired on horizontal surfaces without
affecting the cure.
When slip-proofing is
required, broadcast sand, emery or carborundum into the
first coat while still tacky. Apply the second coat to
seal. |
|
LIMITATIONS: |
| Do NOT
apply when temperature is below 50°F.
Do NOT apply to latex
modified mortar or concrete.
Do NOT place over
working control joint. |
|
CLEAN
UP: |
| Clean tools
and equipment immediately with a suitable solvent such
as xylene or lacquer thinner. |
|
PACKAGING: |
| Clear:
|
Pigmented:
|
|
3 gallon units
15 gallon units
150 gallon units |
2-gallon units
10-gallon units
100-gallon units. |
|
|
CAUTION: |
| For
professional use only. Epoxy systems can cause delayed
dermatitis. Avoid prolonged contact with skin. See
Material Safety Data Sheet for proper handling and
required safety equipment. |
|
PROPERTIES
AT 77°F
| |
CLEAR |
PIGMENTED |
| Mix ratio by volume |
2A:lB |
1A:lB |
| Pot Life (100 Grams) |
30-45 minutes |
30-45 minutes |
| Initial Cure |
4-6 hours |
4-6 hours |
| Viscosity |
500-700 cps |
1000-2000 cps |
| Coverage @ 10 mils |
160 sq. ft. |
160 sq. ft. |
| Tensile Strength (ASTM
D-638) |
3900 psi |
3500 psi |
| Tensile Elongation (ASTM
D-638) |
8% |
5% |
| Abrasion Resistance (ASTM
D-1044) (Tabor Abrader C-10 wheel, 1000 gram load 1000
cycles) |
0.050 |
0.040 |
| Water Absorption |
0.2% |
0.3% |
| Color |
Clear |
Gray, red, tan (other
colors available on special order) |
| Shelf Life |
1 year |
1 year |
|
